Grayhill 60A182060C Optical Encoder Joystick

Grayhill 60A182060C Optical Encoder Joystick Specifications:

• Operating Voltage: 5.00 ± 0.25 Vdc
• Supply Current: 20 mA maximum at 5 Vdc
• Output: Open collector phototransistor
• Output Code: 2-Bit quadrature, channel A leads channel B by 90° electrically during clockwise rotation of the shaft
• Logic Output Characteristics High: No less than 3.5 Vdc
• Logic Output Characteristics Low: No greater than 1.0 Vdc
• Minimum Sink Current: 2.0 mA
• Power Consumption: 100 mW maximum
• Mechanical Life: 1 million rotational cycles
• Average Rotational Torque: 2.0 ± 1.0 inoz initially
• Mounting Torque: 15 in-lbs. maximum
• Shaft Push-Out Force: 45 lbs minimum
• Shaft Pull-Out Force: 45 lbs minimum
• Terminal Strength: 15 lbs terminal pull-out force minimum
• Solderability: 95% free of pin holes and voids
• Pushbutton Rating: 10 mA at 5 Vdc resistive
• Pushbutton Contact Resistance: less than 10 ohms
• Pushbutton Life: 1 million actuations minimum
• Pushbutton Contact Bounce: < 4 mS make, 10 mS break
• Pushbutton Actuation Force: 400 ± 150 grams force
• Joystick Supply Current: 5 mA maximum
• Joystick Angle of Throw: 8° ± 2° in all directions
• Joystick Life: 500,000 actuations in each direction
• Operating Temperature Range: -40°C to 85°C
• Storage Temperature Range: -55°C to 100°C
• Relative Humidity: 96 hours at 90-85% humidity at 40°C
• Vibration: Harmonic motion with amplitude of 15g, within a varied 10 to 2000 Hz frequency for 12 hours
• Mechanical Shock: Test 1: 100g for 6ms half-sine wave with a velocity change of 12.3 ft/s; Test 2: 100g for 6ms sawtooth wave with a velocity change of 9.7 ft/s
• Assembly Studs: 305 Stainless steel
• Detent Housing: Polyamide polymer (nylon 6/10 alloy)
• Printed Circuit Boards: Glass cloth epoxy double clad with copper gold over nickel plated
• Infrared Emitting Diode Chips: Gallium aluminum arsenide
• Silicon Phototransistor Chips: Gold and aluminum alloys
• Resistors: Metal oxide on ceramic substrate
• Solder Pins: Brass, Plated with tin
• Shaft: Polyamide polymer (nylon 6/10 alloy) with stainless steel insert
• Detent Balls: Carbon steel plated with nickel
• Detent Springs: Music wire plated with tin
• Code Rotor: 33% Glass reinforced nylon 66
• Pushbutton Dome: Stainless steel
• Pushbutton Dome Retainer: Polycarbonate
• Joystick Housing: Polyamide polymer (nylon 6/10 alloy)
• Joystick Contact: Stainless steel, silicone rubber, brass with silver cladding, high-temp thermoplastic, phosphor bronze with silver cladding
• Cable: Copper stranded with plating in PVC insulation
• Connector: PA 4.6 with tin over nickel plated phosphor bronze
• Lockwashers: Stainless steel with passivate finish
• Hex Nuts: 303 Stainless steel
• Label: TT406 Thermal transfer cast film
• Solder: Sn/Ag/Cu, Lead-Free, No Clean
• Lubricating Grease: Nye nyogel 774L