Grayhill 62S11M5020C Compact Rotary Encoder

Grayhill 62S11M5020C Compact Rotary Encoder Specifications:

• Operating Temp. Range: -40°C to 85°C
• Storage Temp. Range: -55°C to 100°C
• Humidity: 96 Hours at 90–95% humidity at 40°C
• Mechanical Vibration: Harmonic motion with amplitude of 15G's, within a varied frequency of 10 to 2000 Hz
• Mechanical Shock: Test 1: 100G for 6 mS, half sine wave; Test 2: 100G for 6 mS, sawtooth wave
• Operating Voltage: 5.00 ±0.25 Vdc
• Supply Current: 25mA max at 5.25Vdc
• Output: Open collector phototransistor, external pull up resistors required
• Output Code: 2-Bit quadrature, channel A leads channel B by 90°
• Logic High: ≥ 3.8 Vdc
• Logic Low: ≤ 0.8Vdc
• Minimum Sink Current: 2.0 mA
• Power Consumption: 132mW maximum
• Mechanical Life (Non-Detent): 3 Million Cycles
• Mechanical Life (Low/Medium): 1 Million Cycles
• Mechanical Life (High): 1/2 Million Cycles
• Average Rotational Torque (Low): ±0.50 IN-OZ
• Average Rotational Torque (Medium): ±1.40 IN-OZ
• Average Rotational Torque (High): ±1.60 IN-OZ
• Mounting Torque: 15 in-lbs maximum
• Shaft Push-Out Force: 45 lbs minimum
• Shaft Pull-Out Force: 45 lbs minimum
• Terminal Strength: 15 lbs minimum terminal pull-out force
• Solderability: 95% free of pin holes and voids
• Actuation Force (Pushbutton): 9-950±150 grams, 5-510±150 grams, 4-400±100 grams, 3-300±90 grams, 2-200±75 grams
• Shaft Travel (Pushbutton): .025±.010 inch
• Bushing Material: Zamak 2
• Shaft Material: Aluminum or Zamak 2
• Retaining Ring Material: Stainless steel
• Pushbutton Actuator Material: Zytel 70G33L
• Detent Spring Material: Music wire
• Detent Ball Material: Stainless steel
• Code Housing Material: Polyamide polymer, nylon 6/10 alloy UL94HB
• Code Rotor Material: Delrin 100
• Printed Circuit Board Material: NEMA grade FR-4
• Infrared Emitting Diode Chip Material: Gallium aluminum arsenide
• Silicon Phototransistor Chip Material: Gold and Aluminum Alloys
• Resistor Material: Metal oxide on ceramic substrate
• Solder Pin Material: Brass, plated with tin
• Pushbutton Dome Material: Stainless steel
• Backplate Material: Stainless steel
• Cable Material: Copper stranded with topcoat in PVC insulation
• Connector Material (.050 Center): PA4.6 with tin over nickel plated phosphor bronze
• Connector Material (.100 Center): Nylon UL94V-2, tin plated copper alloy
• Label Material: TT406 Thermal transfer cast film
• Solder Material: Sn/Ag/Cu, Lead-Free
• Lubricating Grease: NYE nyogel 774L
• Hex Nut Material: Nickel, plated with brass
• Lockwasher Material: Zinc Plated Spring Steel with Clear Trivalent Chromate Finish
• Header Material: Hi-Temp glass filled thermoplastic UL94V-0, phoshor bronze
• Strain Relief Material: Glass filled thermoplastic